Label: viadur- leuprolide acetate

Viadur® (leuprolide acetate implant) is a sterile nonbiodegradable, osmotically driven miniaturized implant designed to deliver leuprolide acetate for 12 months at a controlled rate (Figure A). Viadur® incorporates DUROS® technology. The system contains 65 mg of leuprolide (free base). Leuprolide acetate is a synthetic nonapeptide analog of naturally occurring gonadotropin-releasing hormone (GnRH or LH-RH). The analog possesses greater potency than the natural hormone. The implant is inserted subcutaneously in the inner aspect of the upper arm. After 12 months, the implant must be removed. At the time an implant is removed, another implant may be inserted to continue therapy.

Viadur® contains 72 mg of leuprolide acetate (equivalent to 65 mg leuprolide free base) dissolved in 104 mg dimethyl sulfoxide. The 4 mm by 45 mm titanium alloy reservoir houses a polyurethane rate-controlling membrane, an elastomeric piston, and a polyethylene diffusion moderator. The reservoir also contains the osmotic tablets, which are not released with the drug formulation. The osmotic tablets are composed of sodium chloride, sodium carboxymethyl cellulose, povidone, magnesium stearate, and sterile water for injection. Polyethylene glycol fills the space between the osmotic tablets and the reservoir. A minute amount of silicone medical fluid is used during manufacture as a lubricant. The weight of the implant is approximately 1.1g.

Figure A   Viadur® (leuprolide acetate implant) (diagram not to scale)

The chemical name is 5-Oxo-L-prolyl-L-histidyl-L-tryptophyl-L-seryl-L-tyrosyl-D-leucyl-L-leucyl-L-arginyl-N-ethyl-L-prolinamide acetate (salt), with the following structural formula:

Leuprolide acetate, an LH-RH agonist, acts as a potent inhibitor of gonadotropin secretion when given continuously and in therapeutic doses. Animal and human studies indicate that after an initial stimulation, chronic administration of leuprolide acetate results in suppression of ovarian and testicular steroidogenesis.

In humans, administration of leuprolide acetate results in an initial increase in circulating levels of luteinizing hormone (LH) and follicle-stimulating hormone (FSH), leading to a transient increase in concentrations of gonadal steroids (testosterone and dihydrotestosterone in males, and estrone and estradiol in premenopausal females). However, continuous administration of leuprolide acetate results in decreased levels of LH and FSH. In males, testosterone is reduced to castrate levels. These decreases occur within 2 to 4 weeks after initiation of treatment.

One Viadur® Implant nominally delivers 120 micrograms of leuprolide acetate per day over 12 months. Leuprolide acetate is not active when given orally.

In two open-label, non-comparative, multicenter studies, 131 patients with prostatic cancer were treated with Viadur® and evaluated for up to two years. Two-thirds of the patients had stage C or less advanced disease. The dose-ranging study assessed serum testosterone as the primary efficacy endpoint in 51 patients treated with either one [n=27] or two [n=24] implants for 12 months. The confirmatory study evaluated achievement and maintenance of serum testosterone suppression in 80 patients each treated with one implant for 12 months. Both studies included a removal procedure and insertion of a new implant with evaluation for 12 additional months.

Following the initial insertion in patients receiving one implant, mean serum testosterone concentrations increased from 422 ng/dL at baseline to 690 ng/dL on Day 3, then decreased to below baseline by week two (Figure B). Serum testosterone decreased below the 50 ng/dL castrate threshold by week four in all but one patient [106 of 107 patients, 99%]. Once serum testosterone suppression was achieved [one patient was not continuously suppressed until week 28], testosterone remained suppressed below the castrate threshold for the duration of the treatment phase.

Figure B   Mean (+SD) Serum Total Testosterone Concentrations – All Patients (n=107) Who Received One Implant

Most patients [n=118] had a new implant inserted for a second year of therapy following removal of the first implant(s). No patient experienced a clinically significant increase in serum testosterone [acute-on-chronic phenomenon] upon removal of the original implant(s) and insertion of a new implant. Suppression of serum testosterone was maintained in all patients through the two-month follow-up period following removal of the first implant(s) and insertion of a new implant.

Serum Prostate Specific Antigen (PSA) was monitored as a secondary endpoint in the clinical studies with Viadur®. Serum PSA decreased in all patients after they began treatment with Viadur®. At six months, PSA concentrations decreased from baseline by at least 90% in 74.2% of the 97 evaluable patients.

Periodic monitoring of serum testosterone and PSA concentrations is recommended, especially if the anticipated clinical or biochemical response to treatment has not been achieved.

Viadur® is indicated in the palliative treatment of advanced prostate cancer.

1. Viadur® is contraindicated in patients with hypersensitivity to GnRH, GnRH agonist analogs, or any of the components in Viadur®. Anaphylactic reactions to synthetic GnRH or GnRH agonist analogs have been reported in the literature.2
2. Viadur® is contraindicated in women and in pediatric patients and was not studied in women or children. Moreover, leuprolide acetate can cause fetal harm when administered to a pregnant woman. Major fetal abnormalities were observed in rabbits but not in rats after administration of leuprolide acetate throughout gestation. There were increased fetal mortality and decreased fetal weights in rats and rabbits. The effects on fetal mortality are expected consequences of the alterations in hormonal levels brought about by this drug. The possibility exists that spontaneous abortion may occur.

Viadur®, like other LH-RH agonists, causes a transient increase in serum concentrations of testosterone during the first week of treatment. Patients may experience worsening of symptoms or onset of new symptoms, including bone pain, neuropathy, hematuria, or ureteral or bladder outlet obstruction (see PRECAUTIONS).

Cases of ureteral obstruction and spinal cord compression, which may contribute to paralysis with or without fatal complications, have been reported with LH-RH agonists.

If spinal cord compression or renal impairment develops, standard treatment of these complications should be instituted.

The safety of Viadur® was evaluated in 131 patients with prostate cancer treated for up to 24 months in two clinical trials. Viadur®, like other LHRH analogs, caused a transient increase in serum testosterone concentrations during the first 2 weeks of treatment. Therefore, potential exacerbations of signs and symptoms of the disease during the first few weeks of treatment are of concern in patients with vertebral metastases and/or urinary obstruction or hematuria. If these conditions are aggravated, it may lead to neurological problems such as weakness and/or paresthesia of the lower limbs or worsening of urinary symptoms (see WARNINGS and PRECAUTIONS).

In the above-described clinical trials, the transient increase in serum testosterone concentrations was associated with an exacerbation of disease symptoms, manifested by pain or bladder outlet obstructive symptoms (urinary retention or frequency) in 6 (4.6%) patients.

The majority of local reactions associated with initial insertion or removal and insertion of a new implant began and resolved within the first two weeks. Reactions persisted in 9.3% of patients. 10.3% of patients developed application-site reactions after the first two weeks following insertion.

Local reactions after initial insertion of a single implant included bruising (34.6%) and burning (5.6%). Other, less frequently reported, reactions included pulling, pressure, itching, erythema, pain, edema, and bleeding.

In these two clinical trials, four patients had local infection/inflammations that resolved after treatment with oral antibiotics.

Local reactions following insertion of a subsequent implant were comparable to those seen after initial insertion.

In the first 12 months after initial insertion of the implant(s), an implant extruded through the incision site in three of 131 patients (see INSERTION AND REMOVAL PROCEDURES for correct implant placement).

The following possibly or probably related systemic adverse events occurred during clinical trials within 24 months of treatment with Viadur®, and were reported in ≥2% of patients (Table 1).

In addition, the following possibly or probably related systemic adverse events were reported by <2% of patients using Viadur® in clinical studies.

General:  General pain, chills, abdominal pain, malaise, dry mucous membranes

Gastrointestinal:  Constipation, nausea

Hematologic:  Iron deficiency anemia

Metabolic:  Edema, weight loss

Musculoskeletal:  Bone pain, arthritis

Nervous:  Dizziness, insomnia, paresthesia, amnesia, anxiety

Skin:  Pruritus, rash, hirsutism

Urogenital:  Urinary urgency, prostatic disorder, urinary tract infection, dysuria, urinary incontinence, urinary retention

In clinical trials using daily subcutaneous leuprolide acetate in patients with prostate cancer, doses as high as 20 mg/day for up to 2 years caused no adverse effects differing from those observed with the 1 mg/day dose. The adverse event profiles were similar in patients receiving one or two Viadur® implants.

The recommended dose of Viadur® is one implant for 12 months. Each implant contains 65 mg leuprolide. The implant is inserted subcutaneously in the inner aspect of the upper arm and provides continuous release of leuprolide for 12 months of hormonal therapy.

Viadur® must be removed after 12 months of therapy. At the time an implant is removed, another implant may be inserted to continue therapy. (See INSERTION AND REMOVAL PROCEDURES.)

Insertion and Removal Procedures

Viadur® is supplied in a box containing one sterile Viadur® implant in a sealed vial, one Viadur® sterile implanter, one sealed container of lidocaine HCl USP 2%, 10 mL, and one sterile Viadur® Kit. The Viadur® Kit is designed to provide a sterile field and supplies to facilitate the insertion and/or subsequent removal of the implant.

In addition to the Viadur® Kit, sterile gloves are required for the insertion procedure and subsequent removal of the implant.

Insertion Procedure

Under aseptic conditions, an implanter is used to place the implant under the skin.

The implant is inserted using the procedure outlined below.

Identifying the Insertion Site

1. Have the patient lie on his back on the examination table, with his left arm (if the patient is left-handed, the right arm) flexed at the elbow and externally rotated so that his hand is out to his side.
   

   Using a pen and ruler, mark a site on the inner, upper arm approximately 8-10 cm above the elbow crease in the groove between the biceps and triceps muscles. Make sure that the site is unaffected by movement of the muscles.

   

Preparing the Sterile Field

1. To establish a sterile field, carefully open the sterile Viadur® Kit. The sterile kit contains:

   
   

   1 scalpel

   1 forceps

   1 syringe

   1 package povidone-iodine swabs

   1 package wound closure strips

   1-22 Ga x 1.5” needle

   1-25 Ga x 1.5” needle

   6 gauze sponges

   2 alcohol prep swabs

   1 package skin protectant

   1 bandage

   1 fenestrated drape

   1 marking pen

   1 ruler

   1 mosquito clamp

   
2. The implant tray contains:

   
   

   1 sealed vial, which contains the Viadur® implant

   1 sterile implanter

   1 sealed container of lidocaine HCl USP 2%, 10 mL

To open the vial, remove the metal band from the bottle and pull up the stopper. Carefully drop the implant from the bottle onto the sterile field. Then, carefully drop the implanter and the container of lidocaine onto the sterile field.

Using sterile technique, remove the protective cap from the implant by pulling the cap straight off. DO NOT TWIST CAP OFF AS IT MAY UNSCREW THE DIFFUSION MODERATOR, CAUSE ITS REMOVAL, OR OTHERWISE DAMAGE THE IMPLANT. SHOULD DAMAGE OCCUR, DO NOT INSERT THE IMPLANT AS PRODUCT FUNCTION CAN BE IMPAIRED.

Loading the Implanter

1. The implanter is packaged in the correct configuration for implant loading and insertion. Make sure the cannula is fully extended as shown, and the actuator is in its most forward position.
   
2. Using sterile forceps, slide the implant into the end of the cannula and push until it stops. When properly loaded, the implant should not protrude more than 1 mm past the bottom of the beveled edge.
   

Inserting the Implant

1. Using aseptic technique, cleanse the insertion site, then drape the patient's arm. After determining the absence of known allergies to the anesthetic agent, infiltrate the site with lidocaine. Advance the needle to infiltrate the intended 5 cm track for the implant insertion.
   
2. Determine that anesthesia is adequate. Make an incision of approximately 5 mm with the scalpel, just through the dermis.
   
3. Grasp the handle of the implanter and extend the index finger to rest on the back of the actuator as shown. Insert the cannula tip into the incision with the bevel up and advance it subcutaneously along the intended track. To ensure subcutaneous placement, the Viadur® implanter should visibly raise the skin at all times during insertion. The implanter should not enter muscle tissue, but be well within the subcutaneous space. Advance the implanter to the depth indicator on the cannula, which indicates the recommended insertion length.
   
4. Holding the implanter handle in position, use the index finger to slide the actuator slowly back until it stops. (This retracts the actuator cannula into the handle, leaving the implant beneath the skin.). Do not pull back on the implanter handle while sliding the actuator back, as this may lead to incorrect positioning of the implant and subsequent extrusion. Withdraw the implanter from the incision. Release of the implant can be checked by palpation. It is important to keep the implanter steady and not to push the implant into the tissue. After placement, sterile gauze may be used to apply pressure briefly to the insertion site to ensure hemostasis.
   
5. Cleanse the insertion area. Press the edges of the incision together, and tightly close the incision with one or two surgical closure strips. Cover with an adhesive bandage. Observe the patient for a few minutes for signs of bleeding from the incision before he is discharged. Instruct the patient to keep the area clean and dry for 24 hours, and to avoid heavy lifting and strenuous physical activity for 48 hours. The surgical closure strip can be removed as soon as the incision has healed, ie, normally in 3 days.
   

Removal Procedure

Viadur® must be removed following 12 months of therapy.

The position of the patient and the sterile technique are the same as for insertion.

To remove Viadur® use the Viadur® Kit or the following sterile items:

 

1 scalpel

 

1 forceps

 

1 syringe

 

1 package povidone-iodine swabs

 

1 package wound closure strips

 

1-22 Ga x 1.5” needle

 

1-25 Ga x 1.5” needle

 

1 sealed container of lidocaine HCl USP 2%, 10 mL

 

6 gauze sponges

 

2 alcohol prep swabs

 

1 package skin protectant

 

1 bandage

 

1 fenestrated drape

 

1 marking pen

 

1 ruler

 

1 mosquito clamp

Preparing the Site

1. Inspect the site, palpating the location of the implant. Mark the position of the implant with marking pen. Cleanse with povidone-iodine swab. Drape the area with a fenestrated drape.

   
   Suggestion:

   If unable to locate by palpation, radiological imaging may be helpful.

   
2. After determining the absence of known allergies to the anesthetic agent, apply a small amount of local anesthetic under the end of the implant nearest the original incision site. Then advance the needle to infiltrate the tissue along the track.
   

Removing the Implant

1. Determine that anesthesia is adequate. Apply pressure to one end of the implant to elevate the other end. Make an incision of approximately 5 mm at the elevated end of the implant. Do not make a large incision.
   

   Continue to apply pressure to the end of the implant to encourage expulsion. Push the implant gently towards the incision with the fingers. When the tip is visible or near the incision, grasp it with a clamp and remove.

   
2. If necessary, cut through any fibrous encapsulation with the scalpel to free the implant.
3. Properly dispose of removed implant immediately, before opening the vial containing the new implant.

   If inserting a new Viadur®, return to section describing INSERTION PROCEDURE.

   The new Viadur® implant may be placed through the same incision site. Alternatively, the contralateral arm may be used.

4. Cleanse insertion site area. Apply pressure to each end of the incision to close the wound. Apply one or two surgical closure strips to close the wound tightly, and cover with an adhesive bandage. Observe the patient for a few minutes for signs of bleeding from the incision before he is discharged. Instruct the patient to keep the area clean and dry for 24 hours, and to avoid strenuous physical activity for 48 hours.

Viadur® is supplied in a box containing 2 inner package trays. One tray contains a sterile Viadur® implant in a sealed vial, a sterile Viadur® implanter and a sealed container of lidocaine HCl USP 2%, 10 mL. The other tray constitutes a sterile Viadur® Kit, which includes: 1 scalpel, 1 forceps, 1 syringe, povidone-iodine swabs, 1 package wound closure strips, 1-22 Ga x 1.5” needle, 1-25 Ga x 1.5” needle, 6 gauze sponges, 2 alcohol prep swabs, 1 package skin protectant, 1 bandage, 1 fenestrated drape, 1 marking pen, 1 ruler, and 1 mosquito clamp. A physician insert, patient information, and insertion and removal instructions are also provided in the box.

(NDC 0026-9711-01)

Rx Only

Store at 25°C (77°F); excursions permitted to 15-30°C (59-86°F). [see USP Controlled Room Temperature]

For more information call 1-800-288-8371 or visit www.VIADUR.com.

1. Sennello LT et al. Single-dose pharmacokinetics of leuprolide in humans following intravenous and subcutaneous administration. J Pharm Sci 1986; 75(2): 158-160.
2. MacLeod TL et al. Anaphylactic reaction to synthetic luteinizing hormone-releasing hormone. Fertil Steril 1987; 48(3): 500-502.

Manufactured by:
ALZA Corporation
Mountain View, CA 94043 U.S.A.

Distributed by:
Bayer Pharmaceuticals Corporation
400 Morgan Lane, West Haven, CT 06516 USA

Viadur® and DUROS® are registered trademarks of ALZA Corporation under license to Bayer Pharmaceuticals Corporation. For further information about the product contact Bayer Pharmaceuticals Corporation.

An ALZA DUROS® Technology Product

Edition Date: November 2005