Label: STERILE WATER- water injection

Sterile Water for Irrigation, USP

Rx only

Sterile Water for Irrigation, USP is a sterile, hypotonic, nonpyrogenic irrigating fluid or pharmaceutic aid (solvent) entirely composed of Sterile Water for Injection, USP. It is prepared by distillation and contains no antimicrobial or bacteriostatic agents or added buffers.

The pH is 5.7 (5.0-7.0)

The flexible plastic container is made from a multilayered film specifically developed for parenteral drugs. It contains no plasticizers. The solution contact layer is a copolymer of ethylene and propylene. The container is nontoxic and biologically inert. The container-solution unit is a closed system and is not dependent upon entry of external air during administration.

Not made with natural rubber latex, PVC or DEHP.

Sterile Water for Irrigation is utilized for a variety of clinical indications. Because of its low refractive index (1.3325), water provides excellent visibility during endoscopic urological procedures. It is also utilized as a pharmaceutic aid, as well as in the preparation of enteral nutrient products.

Water is hypotonic and will cause hemolysis and will be readily absorbed by the tissues during surgical procedures; therefore, its use under such conditions is not recommended.

Sterile Water for Irrigation is indicated for use as an irrigating fluid or pharmaceutic aid. Sterile Water may also be used as an adjunct in the preparation of non-intravenously administered nutrient mixtures (see DOSAGE AND ADMINISTRATION).

Not for injection.

Sterile Water for Irrigation is hypotonic and will cause hemolysis, and is not recommended for use during surgical procedures.

After opening container, its contents should be used promptly to minimize the possibility of bacterial growth or pyrogen formation.

Discard unused portion of irrigating solution since it contains no preservative.

Use only if solution is clear and container and seal are intact.

None known.

None known.

Sterile Water for Irrigation, USP is supplied sterile and nonpyrogenic in single dose flexible plastic containers.

Exposure of pharmaceutical products to heat should be minimized. Avoid excessive heat. Protect from freezing. Store at 20° to 25°C (68° to 77°F). [see USP Controlled Room Temperature]; however, brief exposure up to 40°C (104°F) does not adversely affect the product.

Not for Injection. Not for use with pressurized irrigation systems.

Check solution container composition, lot number, and expiry date.

Irrigation solutions should be inspected visually for particulate matter and discoloration prior to administration, whenever solution and container permit.

Do not use if the solution is cloudy or precipitate is present.

Check the solution container for leaks by squeezing firmly. If leaks are found, discard.

The intact port cap provides visual tamper evidence. Do not use if port cap is prematurely removed. Maintain strict aseptic technique during handling.

To Add Medication:

1.

Identify WHITE Additive Port with arrow pointing toward solution container.

2.

Immediately before injecting additives, break off WHITE Additive Port Cap with the arrow pointing toward solution container.

3.

Hold base of WHITE Additive Port.

4.

Insert needle (18 – 23 gauge) through the center of the WHITE Additive Port's resealable septum and inject additives.

5.

Mix solution container contents thoroughly.

6.

WHITE Additive port must be swabbed with disinfection agent before re-puncturing.

7.

Check admixture visually for particulate matter.

Preparation for Administration

1.

Immediately before inserting the irrigation set, break off BLUE Administration Port Cap with the arrow pointing away from the solution container.

2.

Use non-vented irrigation set or close the air-inlet on a vented set. Refer to directions for use accompanying the irrigation set.

3.

Hold the base of the BLUE Administration Port, twist and push spike until fully inserted.

4.

The BLUE Administration Port contains a self-sealing septum that helps prevent leakage after removing the spike. The Administration Port is not intended to be spiked more than once.

5.

Suspend solution container from hanger hole.

6.

For Single Use Only. Discard unused portion.

Becton Dickinson and Company
1 Becton Drive
Franklin Lakes, NJ 07417 USA
For product inquiry: 1-800-523-0502
Distributed by BD. Manufactured by Fresenius Kabi.

Made in Germany

451853
Issued: June 2025

soluflex®                 NDC 17271-802-07                  1000 mL

STERILE WATER

FOR IRRIGATION,

USP

INDICATIONS: FOR IRRIGATION

CONTRAINDICATIONS: NOT FOR INJECTION

NDC 17271-802-07               1727180207

Sterile Water for Irrigation,

USP

1,000 mL x 6

STORE AT: 20° to 25°C (68° to 77°F) [see USP Controlled Room Temperature]

Avoid excessive heat. Protect from freezing.

soluflex®               NDC 17271-802-08            2000 mL

STERILE WATER

FOR IRRIGATION,

USP

INDICATIONS: FOR IRRIGATION

CONTRAINDICATIONS: NOT FOR INJECTION

NDC 17271-802-08                 1727180208

Sterile Water for Irrigation,

USP

2,000 mL x 5

STORE AT: 20° to 25°C (68° to 77°F) [see USP Controlled Room Temperature]

Avoid excessive heat. Protect from freezing.

soluflex®      NDC 17271-802-09     3000 mL

STERILE WATER
FOR IRRIGATION,
USP
INDICATIONS: FOR IRRIGATION

CONTRAINDICATIONS: NOT FOR INJECTION

NDC 17271-802-09       1727180209

Sterile Water for Irrigation,
USP
3,000 mL x 4

STORE AT: 20° to 25°C (68° to 77°F) [see USP Controlled Room Temperature]
Avoid excessive heat. Protect from freezing.