HAEMONETICS 0.9 % SODIUM CHLORIDE
|Category||DEA Schedule||Marketing Status|
|HUMAN PRESCRIPTION DRUG LABEL||Abbreviated New Drug Application|
Sodium Chloride Injection, USP is a sterile, nonpyrogenic solution for fluid and electrolyte replenishment in a single dose container for intravenous administration. It contains no antimicrobial agents. The pH is 4.5 to 7.0. Composition, osrnolarity, and ionic concentration are shown below: 0.9% Sodium Chloride Injection, USP contains 9 g/L. Sodium Chloride, USP (NaCl) with an osmolarity of 308 mOsmol/L (cale). It contains 154 mEq/L sodium and 154 mEQ/L chloride. The amount of water that can permeate from inside the container into the overlap in insufficient to affect the solution significantly. Solutions in contact with the plastic container can leach out certain of its chemical components in very small amounts within the expiration period, e.g., di-2-ethylhexyl phthalate (DEHP) up to 5 parts per million. However, the safety of the plastic has been confirmed in tests in animals according to USP biological tests for plastic containers as well as by tissue culture toxicity studies.
Sodium Chloride Injection, USP has value as a source of water and electrolytes. It is capable of inducing diuresis depending on the clinical condition of the patient.
Sodium Chloride Injection, USP is indicated as a source of water and electrolytes. 0.9% Sodium Chloride in hemodialysis procedures.
Sodium Chloride Injection, USP should be used with great care, if at all, in patients with congestive heart failure, servere renal insufficiency, and in clinical states in which there exist ederna with sodium retention. In patients with diminshed renal function administration of Sodium Chloride Injection, USP may result in sodium retention.
Clinical evaluation and periodic laboratory determinations are necessary to monitor changes in fluid balance, electrolyte concentrations, and acid base balance during prolonged parenteral therapy or whenever the condition of the patient warrants such evaluation. Caution must be exercised in the administration of Sodium Chloride Injection, USP to patients receiving corticosteroids or corticotrophin.
Teratogenic Effects. Pregnancy Category C: Animal reproduction studies have not been conducted with Sodium Chloride Injection, USP. It is also not known whether Sodium Chloride Injection, USP can cause fetal harm when administered to a pregnant woman or can affect reproduction capacity. Sodium Chloride Injection, USP should be given to a pregnant woman only if clearly needed.
Safety and effectiveness of Sodium Chloride Injection, USP in pediatric patients have not been established by adequate and well controlled trials; however, the use of sodium chloride solutions in the pediatric populations is referenced in the medical literature. The warnings, precautions and adverse reactions identified in the label copy should be observed in the pediatric population. Do not administer unless solution is clear and seal is intact.
Reactions which may occur because of the solution or the technique of administration include febrile response, infection at the site of injection, venous thrombosis or phlebitis extending from the site of injection, extravasation, and hypervolemia. If an adverse reaction does occur, discontinue the infusion, evaluate the patient, institute appropriate therapeutic counter measures and save the remainder of the fluid for examination if deemed necessary.
As directed by a physician. Dosage is dependent upon the age, weight and clinical condition of the patient as well as laboratory determinations. Parenteral drug products should be inspected visually for participate matter and discoloration prior to administration whenever solution and container permit. All injections in plastic containers are intended for intravenous administration using sterile equipment. Additives may be incompatible. Complete information is not available. Those additives known to be incompatible should not be used. Consult with pharmacist, if available. If, in the informed judgment of the physician, it is deemed advisable to introduce additives, use aseptic techniques. Mix thoroughly when additives have been introduced. Do not store solutions containing additives.
500mL of 0.9% Sodium Chloride Injection, USP are contained in a flexible plastic bag and individually overwrapped. The Product Code is 441A and the NDC is 057826 441. Exposure of pharmaceutical products to beat should be minimized. Avoid excessive heat. It is recommended the product be stored at room temperature (25 degree C): brief exposure up to 40 C does not adversely affect the product.
Warnings: Do not use plastic containers in series connections. Such use could result in air embolism due to residual air being drawn from the primary container before administration of the fluid from the secondary container is completed. To Open Tear overwrap down side at slit and remove solution container. Some opacity of the plastic due to moisture absorption during the sterilization process may be observed. This is normal and does not affect the solution quality of safety. The opacity will diminish gradually. Check for minute leaks by equeezing inner bag firmly. If leaks are found, discard solutions as sterility may be impaired. If supplemental medication is desired, follow directions below. Preparation for Administration 1.Suspend container from eyelet support. 2. Remove plastic protector from outlet port at bottom of container. 3.Attach administration set. Refer to complete directions accompanying set.
WARNING: Additives may be incompatible To add medication before solution administration 1. Prepare medication site. 2. Using syringe with 19 to 22 gauge needle, puncture resealable medication port and inject. 3. Mix solution and medication thoroughly. For high density medication such as potassium chloride, squeeze ports while ports are upright and mix thoroughly. To add medication during solution administration 1.Close clamp on the set. 2. Prepare medication site. 3. Using syringe with 19 to 22 gauge needle, puncture resealable medications port and inject. 4. Remove container from IV pole and/or turn to an upright position. 5. Exacuate both ports by squeezing them while container is in the upright position. 6. Mix solution and medication thoroughly. 7. Return container to in-use position and continue administration.
Each 100 mL contains: Sodium Chloride USP 900 mg Containing 154 mEq/L each of Sodium ion and Chloride ion pH 5.6 (range 4.5 to 7.0) Osmolarity 308 mOsm/L (Calc.) Sterile, nonpyrogenic solution. Single use container. Additives may be incompatible. Consult pharmacist if available. Use aseptic technique when introducing additives. Mix thoroughly. Do not store. Discard unused portion. CAUTION: Squeeze and inspect inner bag which maintains product sterility. Discard if leaks are found. Must not be used in series connections. Do not use unless solution is clear. Do not remove from over wrap until ready for use. The over wrap is a moisture barrier. See Directions for use. May be injected intravenously if directed by physician. Rx only.
Room temperature (25 degree C/77 degree F). Avoid excessive heat. Protect from freezing.
L352, Rev. B Product code 441A Haemonetics Corporation Braintree, MA 02184 USA Lot No. Exp. Date
HAEMONETICS 0.9% Sodium Chloride Injection, USP 500 mL Haemonetics Corporation Braintree, MA 02184 USA
|HAEMONETICS 0.9 % SODIUM CHLORIDE
sodium chloride solution
|Labeler - Haemonetics Corporation (942344649)|