Rx only 

This preparation is designed solely for parenteral use only after addition of drugs that require dilution or must be dissolved in an aqueous vehicle prior to injection.

Sodium Chloride Injection USP, 0.9% is a sterile, nonpyrogenic, isotonic solution of sodium chloride and water for injection. Each mL contains sodium chloride 9 mg. It contains no bacteriostat, antimicrobial agent or added buffer and is supplied only in single-dose containers to dilute or dissolve drugs for injection. Its chloride and sodium ion concentrations are approximately 0.154 mEq of each per milliliter and its calculated osmolality is 0.308 milliosmols per mL. The solution may contain hydrochloric acid and/or sodium hydroxide for pH adjustment, pH 5.3 (4.5 to 7.0).

Sodium chloride, USP occurs as colorless cubic crystals or white crystalline powder and has a saline taste. Sodium chloride is freely soluble in water. The empirical formula for sodium chloride is NaCl, and the molecular weight is 58.44.

Sodium chloride in water dissociates to provide sodium (Na+) and chloride (Cl–) ions. These ions are normal constituents of the body fluids (principally extracellular) and are essential for maintaining electrolyte balance.

The distribution and excretion of sodium (Na+) and chloride (Cl–) are largely under the control of the kidney which maintains a balance between intake and output. The small volume of fluid and amount of sodium chloride provided by Sodium Chloride Injection USP, 0.9% when used only as an isotonic vehicle for parenteral injection of drugs, is unlikely to exert a significant effect on fluid and electrolyte balance except possibly in neonates and very small infants.

Water is an essential constituent of all body tissues and accounts for approximately 70% of total body weight. Average normal adult daily requirement ranges from two to three liters (1.0 to 1.5 liters each for insensible water loss by perspiration and urine production).

Water balance is maintained by various regulatory mechanisms. Water distribution depends primarily on the concentration of electrolytes in the body compartments and sodium (Na+) plays a major role in maintaining physiologic equilibrium.

This parenteral preparation indicated only for diluting or dissolving drugs for intravenous, intramuscular or subcutaneous injection, according to instructions of the manufacturer of the drug to be administered. 

Reactions which may occur because of this solution, added drugs or the technique of reconstitution or administration include febrile response, local tenderness, abscess, tissue necrosis or infection at the site of injection, venous thrombosis or phlebitis extending from the site of injection and extravasation.

If an adverse reaction does occur, discontinue the infusion, evaluate the patient, institute appropriate countermeasures, and if possible, retrieve and save the remainder of the unused vehicle for examination.

Use only as a diluent or solvent. This parenteral preparation is unlikely to pose a threat of carbohydrate, sodium chloride or fluid overload except possibly in neonates or very small infants. In the event these should occur, re-evaluate the patient and institute appropriate corrective measures. See PRECAUTIONS and ADVERSE REACTIONS. 

The volume of the preparation to be used for diluting or dissolving any drug for injection, is dependent on the vehicle concentration, dose and route of administration as recommended by the manufacturer.

This parenteral should be inspected visually for particulate matter and discoloration prior to administration, whenever solution and container permit.

Sodium Chloride Injection USP, 0.9% is supplied in the following:

2 mL vials packaged in carton of 25 vials (NDC 0641-0497-25)

10 mL vials packaged in carton of 25 vials (NDC 0641-6144-25)

To report SUSPECTED ADVERSE REACTIONS, contact Hikma Pharmaceuticals USA Inc. at 1-877-845-0689, or the FDA at 1-800-FDA-1088 or www.fda.gov/medwatch.

For Product Inquiry call 1-877-845-0689.

Manufactured by:

Hikma Pharmaceuticals USA Inc.

Berkeley Heights, NJ 07922

Revised August 2020

462-679-0

NDC 0641-0497-17    Rx only
Sodium Chloride Injection USP, 0.9%
0.308 mOsmol/mL
Preservative Free
For use as a sterile diluent
2 mL Single Dose Vial

NDC 0641-0497-25      Rx only
Sodium Chloride Injection USP, 0.9%
0.308 mOsmol/mL
Preservative Free
For use as a sterile diluent
25 x 2 mL Single Dose Vials

NDC 0641-6144-01
Rx only
Sodium Chloride
Injection USP, 0.9%
0.308 mOsmol/mL
PRESERVATIVE-FREE
For use as a sterile diluent
10 mL Single Dose Vial
Each mL contains sodium
chloride 9 mg in Water for
Injection; pH 4.5-7.0, may
contain hydrochloric acid
and/or sodium hydroxide
for pH adjustment.
Sterile, nonpyrogenic.
Contains no preservative.
Discard unused portion.
For additional information,
see package insert.
Store at 20º-25ºC (68º-77ºF)
[See USP Controlled
Room Temperature].

NDC 0641-6144-25
Rx only
Sodium Chloride
Injection USP, 0.9%
0.308 mOsmol/mL
PRESERVATIVE-FREE
For use as a sterile diluent
25 x 10 mL Single Dose Vials
Each mL contains sodium chloride 9 mg in
Water for Injection; pH 4.5-7.0, may contain
hydrochloric acid and/or sodium hydroxide
for pH adjustment.
Sterile, nonpyrogenic.
Contains no preservative. Discard unused portion.
For additional information, see package insert.
Store at 20º-25ºC (68º-77ºF) [See USP
Controlled Room Temperature].